How to replace a side mirror. How to replace side mirrors on Audi? Replacing the side windows of the VAZ in step-by-step instructions
How to replace the side glass?
By an unfortunate accident, we were left without a side window. But as it turns out, there is no problem in replacing a broken side glass with a new one.
1. Remove the door trim. We lower the glass (more precisely, its remains) to the lowest position.
Replace your rearview mirror yourself
No need to replace the side mirror as a whole, just because the mirror is broken. Here's what you need to restore the mirror mirror. Required for this project. Safety goggles. Gloves. Materials Needed for This Project Avoid last-minute travel to buy missing equipment by preparing ahead of time. Here is a list of what you need. Mirror for pre-cut mirror.
Restore side mirror mirror
Many manufacturers offer pre-cut mirrors that can fit on all makes and models of cars. You will also need a black rubber seal tube available at any auto parts store. Begin the repair by removing as much of the scattered glass from the broken mirror as possible. Be sure to wear leather gloves and goggles to do this. You can leave the old adhesive in place. Then, clean any remaining glass debris and the plastic base of the mirror with a glass cleaner.
2. New glass.
3. Fasteners remained from the old glass. We twist them. One screw on each side and a plastic holder (consisting of two parts - inner and outer).
The new mirror has tapes inside, but don't rely solely on them to keep it in place. Place a good rim of black rubber around the perimeter of the plastic mirror, ¾ inch. from the edge. Place some large hazelnuts of sealant on the honeycomb structure of the plastic base as well as on the old broken mirror. Do not cover areas that will be in contact with the tape. They must fully adhere to the plastic base to properly hold the mirror in place while the sealant dries.
Finally, squeeze the mirror against the base. Use masking tape to hold the mirror in place for the sealant to take effect. If you liked this article, you may be interested in the following links. In late March and April, 12 car petitions were signed in Washington to support changing the law to require the US to be a mirror of a boy.
4. This photo shows the location of the glass fasteners. To access the front glass mount, you need to remove the speaker.
5. Attention for further work it is desirable to have assistants. We insert new glass with a thin side forward from the outside of the door into the grooves of the guides. The deflector from the door and the rubber seal can (better) not be removed. The glass slides into the door with no problems.
Tesla has been trying to draw attention to the problem of reverse mirrors for several years now. But when the concept showed up a year later at the Detroit Auto Show, it had rear-view mirrors. Therefore, the new document could be a significant shift. By the way, even those who have rear-view mirrors.
About cameras to monitor the situation behind the dream car designer for decades. Modern cars are now practically covered by cameras, so there's no reason why they shouldn't be used to replace mirrors. This Japanese automaker uses the camera very clearly. The last view is the display hidden in the interior rear mirror. Under normal conditions, the driver uses it as a classic mirror. For lack of visibility or inclement weather, you can switch to an image that snaps a high resolution camera into the rear of the vehicle.
6. Then we lower the glass to the bottom, to the bar to which it must be screwed and hold it. At this point, we just need help. While you hold the glass, someone must screw it to the power window bar ...
Sriri Nissans are going next year. Mirrors are one of the most important and essential elements in a car. Therefore, it is worth knowing which mirrors and cartridges and how to replace them. This information will not only be useful for you, but also when buying a new car.
Each car is equipped with two types - side and rear. In terms of safety, the most important are the side mirrors, which are used during maneuvers such as changing lanes or overtaking. Rear mirrors are often missing from vans and carts, but in a well-adjusted rear view mirror they will certainly help you with backing or parking behind.
7. ...behind...
8. ... and in front.
And depending on which lens is used in the mirror, the other will be the visibility. Therefore, glass is divided into flat, spherical and aspherical. Flat mirrors can be compared to a piece of mirror - they don't bring the image closer. They are few and far between and you rarely see them today - most often in old used cars.
Replacement tools and materials
The most popular and most used. Because they are made of white glass, they magnify the image, which makes the driver see more of them. On the other hand, the largest field of view is that which is made of broken glass. They also eliminate the so-called. dead point. And what is it and how to eliminate it?
That's all. Glass installed. The most important thing is to carefully collect and pull out the remnants of glass from the door. Better vacuum cleaner with a narrow nozzle
The only thing I forgot to add: It is better not to put the door trim right away. If it's possible to ride on a day 2 car (God knows where the rest of the glass fragments are pouring into the door).
In the current age of mass motorization, when more and more of our fellow citizens become owners of personal vehicles, the subway is full of announcements of new “models” and “cheap” services, and city highways reach the capacity limit, the car rear-view mirror (which is outside, side) is gradually turning into consumable category.
How to eliminate the dead spot in the mirrors?
The deadline is not displayed to the driver sitting behind the wheel in the mirror. Imagine that you are on the right track. You are looking into a mirror that shows the area behind you. You want to change the lane to the left, and suddenly it turns out that it has vehicle. It was a blind spot that you couldn't notice - it was close enough to your car that the mirror didn't cover the area.
Aspherical glass significantly reduces the blind spot area, but does not completely eliminate it. With flat or spherical mirrors, you can do two things: set them correctly so that the smallest part of the car is visible and follow lane change maneuvers. Just one look at the rear side window to see if your vehicle is in the blind spot.
The car owner can become both a victim when a car that rushes past cuts off the causal rear-view device, and the culprit if, through inattention, hits a truck, gazelle, bus (even the cast aluminum frame in the originals will not stand here) or neighbor's mirror. Very often, uncovered mirrors of cars left in the parking lot in places with heavy traffic: on the streets, driveways, etc. turn out to be broken or broken.
Manual, mechanical and electric mirrors
Also remember that by neglecting the dead field, the greatest number of collisions occur. Mirrors can be divided into manual, mechanical and electric. Hand mirrors are among the most inconvenient as they must be placed directly by hand. However, today they are not found in new car models.
These types of mirrors are now widely used and most people talk about mechanical mirrors as manual mirrors. They are controlled by special electronic devices. And you can quickly and conveniently use the left and right mirrors on the left side of the driver button.
Degrees of mirror damage:
- broken mirror element
— broken wind-reflecting panel (overlay)
- total frame damage
Prices for original spare parts differ from the non-original sometimes by an order of magnitude. What to sacrifice - money or quality is up to the owner of the car. The best option is to buy the original, but used - for disassembly or from a private owner. Since the device is not subject to wear and tear, the quality does not suffer at all. But to everything else, low cost and the ability to select colors to match the color of the car are added.
How to replace a car mirror cartridge?
If the mirror in your car has collapsed, you need to replace the cartridge as soon as possible. As has been emphasized several times, mirrors have a huge impact on your safety! You have two choices: replace the glass or the whole glass, i.e. glass with fixation. In both cases, the costs are very similar, but the exchange of the entire deposit will take you much less time.
Therefore, it is much better to buy a quality replacement. And how to take to replace the mirror in the mirror? Install the broken glass first to create a gap between the mirror and the mirror body. Then carefully glaze the glass and carefully remove the cartridge. If you decide to buy a new cartridge, just install it in the opposite direction from where you pulled out the old slides.
The process of replacing the mirror, oddly enough, surprises with its ease. A new lining is enough only to snap into the grooves. The mirror element is usually also placed on the latches. In rare cases, it will have to be glued, remembering to remove the remnants of the old glue with methanol. When replacing the element in heated models, special care must be taken not to damage the printed wiring.
The procedure for replacing the mirror "assembly"
1. The handle for adjusting the position of the mirror inside the passenger compartment is removed (for models with manual adjustment)
2. The door panel is removed, hiding the mount, inside the cabin (sometimes a speaker is built into it)
3. Disconnect the mirror wiring (for models with electric adjustment and heating)
4. 3 mounting bolts are unscrewed (usually a cross head). Here you should be wary of falling bolts inside the door skin: it will not be easy to get them out of there. It is best to play it safe and close the hole with a rag.
5. We take out the latches on the mirror housing from the holes in the door. Similarly, we insert the latches of the new device there. We assemble in the reverse order.
Related Articles
